<\/div>\n\n\n\n
Start by letting the engine run for approximately 5\u201310 minutes<\/strong>.<\/p>\n\n\n\n<\/div>\n\n\n\n
This helps increase the temperature of the engine oil, making it thinner and allowing it to drain out more easily and completely.<\/p>\n\n\n\n
<\/div>\n\n\n\n
However, be careful not to overheat the engine, as extremely hot oil can cause burns while working underneath the vehicle.<\/p>\n\n\n\n
<\/div>\n\n\n\n
\n\n\n\n
<\/div>\n\n\n\n
<\/span>2. Lift the Vehicle and Prepare the Workspace<\/strong><\/span><\/h3>\n\n\n\n<\/div>\n\n\n\n
Park the vehicle on a flat surface and firmly engage the parking brake.<\/p>\n\n\n\n
<\/div>\n\n\n\n
Use a car jack to lift the vehicle, then securely place it on jack stands before working underneath.<\/p>\n\n\n\n
<\/div>\n\n\n\n
One important safety rule:<\/p>\n\n\n\n
<\/div>\n\n\n\n
Never work under a vehicle supported only by a jack.<\/strong><\/p>\n\n\n\n<\/div>\n\n\n\n
Always use proper jack stands to prevent accidents.<\/p>\n\n\n\n
<\/div>\n\n\n\n
\n\n\n\n
<\/div>\n\n\n\n
<\/span>3. Drain the Old Engine Oil<\/strong><\/span><\/h3>\n\n\n\n<\/div>\n\n\n\n
Once the vehicle is safely lifted, locate the oil drain plug underneath the oil pan.<\/p>\n\n\n\n
<\/div>\n\n\n\n
Place the oil drain pan directly beneath the drain plug.<\/p>\n\n\n\n
<\/div>\n\n\n\n
Use the appropriate wrench to loosen the drain bolt carefully. Once the bolt becomes loose, continue turning it by hand until it comes off completely, then allow the old oil to drain fully.<\/p>\n\n\n\n
<\/div>\n\n\n\n
Be cautious during this step, as the engine oil may still be hot.<\/p>\n\n\n\n
<\/div>\n\n\n\n
\n\n\n\n
<\/div>\n\n\n\n
<\/span>4. Replace the Oil Filter<\/strong><\/span><\/h3>\n\n\n\n<\/div>\n\n\n\n
While waiting for the old oil to finish draining, remove the old oil filter using the oil filter removal tool.<\/p>\n\n\n\n
<\/div>\n\n\n\n
After removing it:<\/p>\n\n\n\n
<\/div>\n\n\n\n
\n- Clean the filter mounting surface thoroughly using a clean cloth<\/li>\n\n\n\n
- Apply a thin layer of fresh engine oil to the rubber seal of the new oil filter<\/li>\n<\/ul>\n\n\n\n
<\/div>\n\n\n\n
This helps create a better seal and makes future removal easier.<\/p>\n\n\n\n
<\/div>\n\n\n\n
Install the new oil filter by hand until snug.<\/p>\n\n\n\n
<\/div>\n\n\n\n
Avoid overtightening, as excessive force may damage the rubber seal.<\/p>\n\n\n\n
<\/div>\n\n\n\n
\n\n\n\n
<\/div>\n\n\n\n
<\/span>5. Reinstall the Oil Drain Plug<\/strong><\/span><\/h3>\n\n\n\n<\/div>\n\n\n\n
Once the old oil slows down to small drips, replace the drain plug washer with a new one.<\/p>\n\n\n\n
<\/div>\n\n\n\n
Reinstall the drain bolt and tighten it securely, but do not overtighten.<\/p>\n\n\n\n
<\/div>\n\n\n\n
Proper torque is important to prevent both leaks and thread damage.<\/p>\n\n\n\n
<\/div>\n\n\n\n
\n\n\n\n
<\/div>\n\n\n\n
<\/span>6. Fill with New Engine Oil<\/strong><\/span><\/h3>\n\n\n\n